View MC10H180FN_744182.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10H180 Dual 2-Bit Adder/Subtractor
The MC10H180 is a high-speed, low-power, general-purpose adder/ subtractor. It is designed to be used in special purpose adders/subtractors or in high-speed multiplier arrays. Inputs for each adder are Carry-in, Operand A, and Operand B; outputs are Sum, Sum and Carry-out. The common select inputs serve as a control line to Invert A for subtract, and a control line to Invert B. * Propagation Delay, 1.8 ns Typical, Operand and Select to Output * Power Dissipation, 360 mW Typicalh180 * Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) * Voltage Compensated * MECL 10K-Compatible
LOGIC DIAGRAM
7 9 5 6 4 SELA S0 S0 SELB AO BO CIN COUT 15 2 PDIP-16 P SUFFIX CASE 648 1 3 PLCC-20 FN SUFFIX CASE 775 1 10H180 AWLYYWW
http://onsemi.com MARKING DIAGRAMS
16 CDIP-16 L SUFFIX CASE 620 1 16 MC10H180P AWLYYWW MC10H180L AWLYYWW
11 10 12
SELA S1 S1 SELB A1 B1 CIN COUT VCC = PIN 16 VEE = PIN 8 POSITIVE LOGIC ONLY A' = A SELA = ASELA B' = B SELB = BSELB S = CIN (A' B' + A' B') + CIN(A' B' + A' B') COUT = CINA' + CINB' + A' B'
14 1
13
A WL YY WW
= Assembly Location = Wafer Lot = Year = Work Week

ORDERING INFORMATION
Device MC10H180L MC10H180P MC10H180FN Package CDIP-16 PDIP-16 PLCC-20 Shipping 25 Units/Rail 25 Units/Rail 46 Units/Rail
DIP PIN ASSIGNMENT
S1 S0 COUT CIN A0 B0 SELA VEE 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC S0 S1 COUT CIN A1 B1 SELB
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 18 of the ON Semiconductor MECL Data Book (DL122/D).
(c) Semiconductor Components Industries, LLC, 2000
1
March, 2000 - Rev. 6
Publication Order Number: MC10H180/D
MC10H180
MAXIMUM RATINGS
Symbol VEE VI Iout TA Tstg Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current - Continuous - Surge Operating Temperature Range Storage Temperature Range - Plastic - Ceramic Characteristic Rating -8.0 to 0 0 to VEE 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C C
ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (See Note 1.)
0 Symbol IE IinH Characteristic Power Supply Current Input Current High Pins 4, 12 Pins 7, 9 Pins 5, 6, 10, 11 Input Current Low High Output Voltage Low Output Voltage High Input Voltage (1) Low Input Voltage (1) Min - - - - 0.5 -1.02 -1.95 -1.17 -1.95 Max 95 665 515 410 - -0.84 -1.63 -0.84 -1.48 Min - - - - 0.5 -0.98 -1.95 -1.13 -1.95 25 Max 86 417 320 255 - -0.81 -1.63 -0.81 -1.48 Min - - - - 0.3 -0.92 -1.95 -1.07 -1.95 75 Max 95 417 320 255 - -0.735 -1.60 -0.735 -1.45 A Vdc Vdc Vdc Vdc Unit mA A
IinL VOH VOL VIH VIL tpd
AC PARAMETERS
Propagation Delay Operand to Output Select to Output Carry-in to Output ns 0.6 0.6 0.4 2.4 2.2 1.6 0.7 0.7 0.4 2.5 2.3 1.7 0.8 0.8 0.4 2.8 2.6 1.8
tr Rise Time 0.5 2.0 0.5 2.1 0.5 2.2 ns tf Fall Time 0.5 2.0 0.5 2.1 0.5 2.2 ns 1. Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts.
FUNCTION SELECT TABLE
SelA H H L L Function SelB S = A plus B H L H L S = A minus B S = B minus A S = 0 minus A minus B
TRUTH TABLE
INPUTS FUNCTION SelA ADD H H H H H H H H H H H H H H H H SelB H H H H H H H H L L L L L L L L A0 B0 L L L L H H H H L L L L H H H H L L H H L L H H L L H H L L H H Cin L H L H L H L H L H L H L H L H S0 S0 Cout L H H L H L L H H L L H L H H L H L L H L H H L L H H L H L L H L L L H L H H H L H L L H H L H REVERSE SUBTRACT FUNCTION SelA L L L L L L L L L L L L L L L L SelB H H H H H H H H L L L L L L L L A0 B0 L L L L H H H H L L L L H H H H L L H H L L H H L L H H L L H H Cin L H L H L H L H L H L H L H L H S0 S0 Cout H L L H L H H L L H H L H L L H L H H L H L L H H L L H L H H L L H H H L L L H H H L H L H L L INPUTS
SUBTRACT
http://onsemi.com
2
MC10H180
PACKAGE DIMENSIONS
PLCC-20 FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C
B -N- Y BRK D -L- -M- W D X V A Z R 0.007 (0.180) M T L-M
S
0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
Z
20
1
G1
0.010 (0.250)
S
T L-M
S
N
S
VIEW D-D 0.007 (0.180) M T L-M
S
N N
S
H
0.007 (0.180) M T L-M
S
N
S
S
K1 K
C
E 0.004 (0.100) G G1 0.010 (0.250) S T L-M J -T-
SEATING PLANE
F VIEW S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
0.007 (0.180) M T L-M
S
N
S
VIEW S
S
N
S
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
http://onsemi.com
3
MC10H180
CDIP-16 L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE T
-A-
16 9
-B-
1 8
C
L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01
-T-
SEATING PLANE
N E F D G
16 PL
K M J
16 PL
0.25 (0.010)
M
M
TB
S
0.25 (0.010)
TA
S
-A-
16 9
PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R
B
1
8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H G D
16 PL
SEATING PLANE
K
J TA
M
M
0.25 (0.010)
M
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
4
MC10H180/D

▲Up To Search▲

Price & Availability of MC10H180FN

	To Download MC10H180FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .